To force air and oxygen into livewells to keep fish or bait alive. Also, to force air under the running surface of a hull.
The rear of the boat.
Sleeping quarters beneath the aft or rear section of the boat (sometimes called a mid cabin when located beneath the helm).
The side of a boat or object away from the direction of the wind.
Above deck in the rigging.
Small, lightweight, durable trailerboat constructed of aluminum that is either welded or riveted; generally used for freshwater fishing.
Center section of a boat.
A location intended or suited for anchoring.
A special paint applied to a boat’s hull to prevent marine growth.
The direction and velocity of wind as felt in a moving boat.
The direction toward or beyond the stern.
Perpendicular to a boat’s centerline
An anchor that is off the bottom.
The relationship of revolutions of a tow vehicle’s axle to that of its driveshaft or transaxle, e.g. 2.74:1.
Maneuvering in reverse when offshore fishing while attempting to land a fish.
A support for the mast to keep it from falling forward.
To remove water with a bucket or pump. Also, a component that controls fishing line on a spinning reel.
Area on a fishing boat for preparing bait.
Compartment on a fishing boat for holding live bait, usually with a pump to circulate the water and an aerator to provide oxygen.
Weight added to the bottom of a boat to improve stability.
Low-profile, outboard-powered boat, generally no more than 22 feet long and typically equipped with rod lockers, casting decks with pedestal seats and livewells.
Low-profile, inshore fishing boat intended for use in protected coastal waters, and frequently made with rolled-edge construction.
Small, lightweight sailboat less than 25 feet long that can be easily launched and retrieved from a beach.
Measurement of a boat at its widest point. Also, a transmitted radio, sonar or radar signal.
To turn away from the wind.
Direction to an object.
A place to sleep aboard a boat. Also, a boat slip.
Lowest section inside a boat’s hull where water collects.
A canvas cover over the helm or cockpit area.
Vertical post extending above the deck to secure docking lines.
Mid-size to large deep-V boats suitable for offshore fishing. They are typically fitted with outriggers, fish boxes, aluminum towers, a host of electronics and large fuel tanks.
A spar attached to a sail at its foot.
Forward portion of a boat.
A stainless steel U-bolt on a boat’s bow stem used to secure tow lines or trailer winch hooks.
Rubber blocks on a boat trailer into which the boat’s stem rests.
A runabout boat with open-bow seating.
A spar extending forward of the bow on a sailboat.
Emergency safety cable on a boat trailer that activates trailer brakes in the event the trailer comes detached from the tow vehicle while underway.
Distance from waterline to a boat’s highest point.
Transverse wall in a boat that usually bears weight and supplies hull support.
Long carpeted sections of a boat trailer that support the boat’s weight.
An anchored floating object that serves as a navigation aid. Also used to mark a mooring spot.
Small flag that bears a yacht club’s symbol.
Curvature of a sail.
Cylindrical navigation buoy with a flat top, generally green in color.
To flip a boat over.
A winch used for hauling heavy objects such as anchors.
To unfasten all lines in preparation for departure.
Elevated deck clear of obstruction used by anglers to make casts, often equipped with pedestal chairs.
A twin hulled boat, either power or sail.
Small, simple sailboat with one mast and sail set far forward.
Inefficient low-pressure pockets on propellers form bubbles that collapse against the blades resulting in premature wear.
Fishing boat with the helm station located amidships for maximum walk-through space around the perimeter of the boat.
A keel-like pivoting device, typically in a trunk, that can be lowered or raised to act as a keel.
The navigable portion of a waterway.
Electronic navigation device that displays charts for use in plotting a course.
An electronic depth sounder that records bottom structure data on paper.
Paper or electronic navigation maps.
Portion of the hull where the bottom and sides intersect (can be rounded or angled).
Fiberglass strands cut and simultaneoulsy mixed with resin by and applied to a boat mold by using a chopper gun.
Placing fish or fish parts in the water to attract gamefish.
Trailer hitch with a weight-carrying capacity up to 2,000 pounds; available as a bumper mount, step bumper or bumper/frame mount.
Frame-mounted trailer hitch with a weight-carrying capacity of up to 3,500 pounds.
Frame-mounted trailer hitch with a weight-carrying capacity of up to 5,000 pounds.
Frame-mounted trailer hitch with a weight-carrying capacity of up to 10,000 pounds.
Hardware piece on a boat or a dock to which lines are attached.
The after-most corner of a sail.
Sailing as close to the wind as possible.
A raised edge, as around the cockpit or around a hatchway, to keep water out.
Basic safety gear required by federal law consisting of personal flotation device, throwable flotation device, visible distress signals, fire extinguisher and a horn, whistle or bell.
Deck space for the crew of a boat, typically recessed.
Coast Guard term for the navigation rules of the road; full name is International Regulations for Preventing Collisions at Sea.
To tack or change heading relative to the wind.
Entryway from the deck to the belowdeck cabin area.
A bluewater fishing boat typically more than 35 feet long with a full cruising salon, a fish-fighting cockpit and many other saltwater fishing features.
Any of a variety of lightweight materials used between layers of fiberglass laminates to add strength.
The act of two propellers spinning in opposite directions on a single shaft.
Component on a boat trailer that connects to the hitchball.
Direction in which a boat is steered.
A boat with overnight accommodations.
Belowdecks accommodations in the bow area for overnighting and stowage.
Hardening process for resin-soaked fiberglass laminates.
Attachable front and side enclosures that protect the helm area from weather.
Single-masted sailboat similar to a sloop, but with the mast farther aft to allow for a double headsail.
A keel-like device that is manually raised and lowered vertically without using a hinge.
A small crane used to hoist a boat or dinghy or other object.
To go sailing for a few hours on a small, open sailboat.
Small, open sailboat sometimes raced or short-distanced cruised, primarily used for recreational sailing.
Directly ahead of the bow.
Degrees of V-shape hull angle measured at the transom of planing powerboats.
Blunt-bowed power boat generally characterized by an open deck and generous passenger seating.
A hull shape characterized by a sharp deadrise, typically more than 20 degrees.
Electronic sonar device that displays water depth.
The amount of error from displaying magnetic north in a boat’s compass caused by the boat’s own magnetic interference.
A highly accurate global positioning system (GPS) that utilizes a differential radio beacon and receiver to compute and correct the error of all visible satellites sending data to a conventional GPS unit.
A small dining area usually consisting of a table and facing bench seats; it can often be converted into a berth.
A small sailboat often raced that can be sailed on and off a beach. Also a tender, either rowed or equipped with power, used to go to and from a larger vessel.
An engine configuration in which the drive shaft runs in a straight driveline through the bottom of the hull.
The weight of water displaced by a hull. Also, a type of hull that smoothly displaces water as opposed to riding on top of it.
A hull shape designed to run through water rather than on top of it in the manner of a planing hull.
A gunwale-mounted weighted line device used for deep-water trolling.
Vertical distance a boat penetrates the water.
A parachute-like sea anchor.
Weight of the boat without fuel and fresh water.
A type of boat with twin dashboards separated by a centerline walk-through deck leading to the bow.
Acronym for emergency positioning indicating radio beacon. When this electronic device is activated it transmits a radio signal with user registration data and positioning information to a network of satellites that assist the Coast Guard in conducting an emergency rescue.
A cruising boat without a deck-level salon. Sometimes called a sunbridge cruiser.
Nautical depth measurement equaling six feet.
A cylindrical or round cushion used to protect the hull sides of a boat, typically used when tied up at dock.
To clear a buoy, point of land or object without having to make a tack.
Glass fibers either loose or woven, reinforced with resin and used in the construction of many boats.
A fix-mounted chair used to help land large gamefish on bluewater fishing boats equipped with a footrest, gimbal-mounted rod holder, safety harness and other fish-fighting gear.
A keel shaped like the fin of a fish that is shorter and deeper than a full-length keel.
Electronic device that uses sonar to locate and display fish on a monitor.
The position of a boat recorded in coordinates or bearings.
A pyrotechnic device used to indicate distress. Also, the outward curvature of the sides on the bow of a boat.
Type of boat or hull shape with very little or no deadrise.
Type of small, inshore saltwater fishing boat with moderate deadrise and draft, usually equipped with a raised platform aft used by a guide pushing a long pole to silently maneuver the boat through shallow tidal water.
Raised, second-story helm station, often located above the primary helm.
Wave pattern running in the same direction as the boat.
The bottom edge of a sail.
Located at the front of a boat.
Forward part of the main deck, ahead of the superstructure.
Jacket, pants and hat used during inclement weather.
A gasoline- or diesel-powered internal combustion engine that takes four cycles or strokes of the piston to complete its power phase. Also called four-stroke engine.
Hitch fastened to the frame of a tow vehicle.
Vertical distance between the waterline and the top of the hull side.
Rolling or folding a sail on its boom.
A metal pole with a hooked end used to boat a fish. Also a pole or spar that holds the upper portion of a four-sided sail.
The kitchen area on a boat.
A combination of resin and pigment that comprises the smooth outside coating of a fiberglass boat.
An overlapping jib.
Another name for a gas- or disel-powered electric generator.
Yield to other traffic.
Acronym for global positioning system, a satellite-based navigation system that uses trasmitted signals and mathematical triangulation to pinpoint location.
The maximum weight an axle is designed to carry.
The maximum allowable weight of a fully loaded tow vehicle plus its fully loaded trailer, including passengers and cargo.
The maximum allowable weight of trailer and its cargo.
The maximum allowable weight of a fully equipped tow vehicle including passengers and cargo.
To explore creeks, coves marshes or other shallow areas near shore.
The upper edge of the side of a boat.
Also spelled jibe. To change the course of a boat so that the boom swings over to the opposite side.
Line used to hoist a spar or sail.
The person at a harbor in charge of anchorages, berths and harbor traffic.
A sharp-angle at the intersection of the hull’s side and bottom.
Turning the steering wheel or tiller all the way in one direction.
A large fiberglass roof or platform over the helm area.
A deck opening.
To lift a boat from the water.
Fittings in the deck or gunwale through which the anchor rode or dock lines run.
Toilet facilities or room where they are located.
Waves coming from the direction a boat is heading.
The direction a boat is pointed.
Any sail set forward of the mast.
Forward motion of a boat in the water.
To pull on a line. Also to throw a line.
Setting the sails so the boat makes little headway, either used in a storm or a waiting situation.
To temporarily tip or lean to one side.
Area of a boat where operational controls are located.
A type of boat capable of running at high speeds, often equipped with high-horsepower and exotic propulsion systems, sometimes used for racing.
To lean out on the windward side of a sailboat to achieve optimal speed by offsetting heeling.
Steel framework on a tow vehicle used to hook up a trailer.
The ball-shaped component of the hitch that fits into the trailer coupler.
Storage tank for gray water.
A large, flat-bottom boat with square sides and house-like characteristics, such as comfortable furniture and living accommodations.
The structural body of the boat that rests in the water.
An internal combustion engine often mounted amidships that runs a drive shaft through the hull bottom.
See stern drive.
Capable of being inflated either with air, as in a life raft or life vest.
A type of boat with air chambers into which air is pumped either manually or automatically for buoyancy, some having rigid bottoms.
Smooth-finished, molded fiberglass structure adjacent to the inside portion of the hull.
Device that changes 12-, 24- or 32-volt direct current (DC) from a battery to 120-volt alternating current (AC).
A mounting device for an outboard motor that enables operators to vertically raise or lower the motor, thereby controlling propeller depth in the water.
A boat powered by an engine with a water-pump used to create propulsion.
Triangular sail projecting ahead of the mast.
The bottom-most portion or longitudinal centerline of a hull.
A sailboat similar in appearance to a yawl with a tall main mast and a shorter mizzen mast ahead of the rudder post.
A small auxiliary outboard motor.
A switch with a lanyard that automatically shuts off an engine if disconnected.
A technique that involves attaching a fishing line to a kite to present bait at a distance from the boat.
Speed measured in nautical miles per hour.
A single layer of material used in multi-layered fiberglass construction.
A list of the sequential layers of materials used in fiberglass construction.
Geographic distance north or south of the equator expressed in degrees and minutes.
Wide, padded bolster at the helm used instead of or in lieu of conventional seats.
Direction toward which the wind blows.
The side of an object that is sheltered from the wind.
To slip sideways downwind while moving forward.
Safety lines on deck that are grabbed to prevent falling overboard.
A continuous lean to one side due to improper weight distribution.
Compartment on a fishing boat designed to keep fish or bait alive.
Length overall; the distance between the most forward part of the boat and the most aft part.
A stowage compartment, whether equipped with a lock or not.
Geographic distance east or west of the prime meridian expressed in degrees and minutes.
Electronic navigation system that measures the time difference in the reception of radio signals from land-based transmitters.
Also known as a gearcase, the lower unit is the bottom part of an outboard or stern drive motor where the propeller is located.
The leading edge of a sail.
The largest regular sail on a sailboat.
To secure a line.
The addition of marine components to automotive engines.
Vertical spar that supports sails.
A radio distress call.
A large, luxurious yacht, typically longer than 100 feet
Location near the center of a boat.
A shorter mast located aft of the main mast on a yawl or ketch.
A modification of the deep-V hull shape with a deadrise of less than 20 degrees.
A hollow reinforced cavity that is the mirror-image or reverse-image of the boat and into which fiberglass, gel coat and resin are laid during composite-hull construction.
A boat with a single hull.
Permanent ground tackle fixed to a buoy that boats can tie to.
A hybrid boat that has sails and powerful engines.
A large powerboat greater than 40 feet with luxurious interior accommodations for long-range cruising.
A boat with more than one hull, such as a catamaran or trimaran.
A distance of 6,076.12 feet or 1,852 meters, which is about 15 percent longer than a statute mile. Equivalent to one minute of latitude on a navigation chart.
Conical navigation buoy that is usually red.
Support device for mounting outboard engines that extends aft of the transom.
Internal combustion engine mounted at the transom that incorporates motor, driveshaft and propeller.
The lower unit of a stern-drive motor that houses the drive gears and to which the propeller fastens.
Poles designed to spread out fishing lines and keep them from tangling while trolling.
Over the side of a boat and into the water.
A safety vest or jacket capable of keeping an individual afloat.
A small, lightweight craft designed to be either sat-on or stood-on with motorcycle-like handlebars and squeeze throttle, usually jet-propelled.
A post driven into the ground below the waterline to support a pier, dock, etc.
A fully enclosed helm compartment.
Theoretical distance a propeller would travel in one revolution. Also, the rise and fall of a boat’s bow and stern.
A boat hull designed to ride on top of the water rather than plowing through it.
Recreational day boating in runabouts, deck boats, pontoon boats, bowriders and sportboats.
To plan a navigation course using a chart.
Small elevated stand on a flats boat used by a fisherman to silently pole through shallow water and scout for fish.
A type of boat with a flat deck attached to airtight flotation tubes or logs.
The left side of a boat when facing the bow. Also, a marina harbor or commercial dock.
A multihulled powerboat with two identical side-by-side hulls.
A powerboat with overnight accommodations, typically up to 40 feet long.
A rotating multi-blade device that propels a boat through the water.
Forward deck and railing structure at the bow of a boat.
See personal watercraft.
The after side of a boat from amidships to stern.
The practice of aiming the boat’s bow at a 45-degree angle to oncoming waves.
Living and sleeping areas of a vessel.
A sailboat designed primarily for speed and competition with a minimum of built-in creature comforts.
A fast sailboat designed with comfortable accommodations.
Electronic device using high frequency radio waves to detect objects and display their positions on a monitor.
Distance a boat can travel at cruising speed on a tank of fuel. Also, the distance to an object. Lastly, in intracoastal navigation, a set of two markers that, when lined up one behind the other, indicate the deepest part of the channel.
To sail across the wind.
Last warning given by a helmsman before tacking and turning the bow into the wind, notifying the crew that the boom and sail will cross the boat.
Part of a hitch that receives and holds the hitch bar or shank.
A hitch with a receiver from which a hitch bar or shank can be removed.
Liquid substance used in fiberglass composite construction that, when combined with a catalyst, bonds laminate materials together.
A chine that angles downward from the hull designed to direct spray out and awayfrom the boat.
An inflatable boat fitted with a rigid bottom.
Wire cables, rods, lines, hardware and other equipment that support and control the mast and spars.
A device designed for a fishing boat that bolts to the cockpit floor or is incorporated into a bench seat, to hold multiple fishing rods.
Device designed to safely and securely hold fishing rods either vertically or horizontally.
Line, chain, cable or any combination of these used to connect the anchor to the boat.
A fishing boat designed to run in coastal waters constructed of a simple, one-piece fiberglass hull without a top deck and characterized by rounded top edges without true gunwales.
A trailer outfitted with rollers instead of bunks.
Protective outer bumper that runs around the boat at the point where the top deck meets the hull.
Underwater fin mounted below the hull near the stern that controls boat steering.
A kind of small, lightweight, freshwater pleasurecraft intended for day use.
Required navigation lights that a vessel uses at night to indicate position and status.
Lines used in the setting and trimming of sails.
Legally mandated chains that connect the trailer to the tow vehicle as a safety measure in case the coupler detaches.
A harness worn by a boater attached to the boat with a tether to reduce the chances of going overboard.
To slide or drift off course.
Arrangement of sails on a boat.
A boat that is at least partially propelled by capturing the force of wind in sails.
Full-sized, well-appointed cabin on the main deck level of a motoryacht, convertible or megayacht used for entertaining.
Any fishing boat used in the ocean or coastal waters that’s specially equipped to handle the harsh saltwater environment.
A large sailboat with two or more masts where the foremast is shorter than aft mainmast.
The ratio of anchor rode to vertical depth.
To run before the wind in bad weather.
Gravity fed drain in a boat to allow water to drain out and overboard.
To cut holes or open ports to purposely let water in to make a boat sink.
Gossip. So named after a water cask around which sailors used to gather and drink.
A canvas, cone-shaped device deployed to keep the bow headed into the wind to help safely ride out a storm. Also called a drogue.
Through-hull fitting with a valve between the interior and the exterior of the boat.
Ability to handle rough weather. Also called sea-kindly.
A type of large boat equipped with a salon and a raised helm or bridge.
Intentional degradation of GPS signal used for position fixing by the U.S. Department of Defense for purposes of national security. With selective availability turned on, positions can be fixed to about 300 meters. With selective availability turned off, positions can be fixed to about 100 meters.
Drains water overboard automatically. Self–bailing boats, or self–bailing hulls, are designed to remove water from the boat deck or cockpit area using gravity not pumps of any kind. … Self–bailing, actually being somewhat of a misnomer, means that gravity and momentum are used to rid a boat of unwanted water.
A hull shape with soft chines or a rounded bottom that enables the boat to achieve minimal planing characteristics.
Line of the deck or gunwale from bow to stern as viewed from outside the boat.
Line used to trim a sail.
Mast support rigging, usually a wire, that runs from the mast to the side of the boat.
A dash-panel unit affixed to the side of a boat. If only one, helm controls are affixed to it.
A fin or vertical projection below the hull that provides directional stability. Also, a fin-like projection at the bottom of an outboard.
A small, simple, shallow-draft boat.
Low profile, pleasure boats with minimal deadrise specifically designed for waterskiing and/or wakeboarding. These boats are usually characterized by an inboard engine and a towing pylon. Wakeboard boats are often equipped with a tower or extremely tall pylon to fasten the tow line in a manner to aid vertical jumping and water-ballast devices to increase the weight of the boat.
A boat berth between two piers or floats. Also, the slight loss of efficient power delivery as a propeller spins in the water.
A single-masted sailboat in which the mast is set forward of midships.
The deck floor.
A method to locate objects and determine distance by transmitting sound waves through water and measuring the time it takes the echo to bounce back. Used in depth finders and fishfinders.
Charted water depth.
Masts, booms, gaffs and poles used in sailboat rigging.
A type of bluewater fishing boat with at least two sleeping cabins and many dedicated fish-fighting features.
A docking line attached amidships to control fore and aft movement.
An order to crewmen to be ready, be prepared.
Maintain course and speed.
The shrouds and stays that support the mast but are not adjusted while working a boat.
The right side of the boat looking toward the bow.
A room with sleeping quarters, a cabin.
Distance of 5,280 feet, the standard measure of distance on land and most inland waterways.
Wire, rod or other rigging that runs fore and aft of the mast.
The most forward section of the hull.
Socket that holds the base of the mast.
A high-performance hull design with lateral notches, or steps, in the keel.
Aft portion of a boat.
Propulsion system composed of an inboard engine connected to a steerable drive unit extending through a cut-out in the transom.
To put an object away onboard a boat, to store.
Small linear protrusions that run longitudinally on both sides of the keel to give a planing hull lift and lateral stability.
Internal beams and braces that give a fiberglass hull structural support.
Hydraulic trailer brake system activated by the sudden inertia of a trailer pushing against the tow vehicle during a hard stop.
To fill a boat with water.
Side-to-side wandering of a trailer under tow.
A wide platform at the transom equipped with a ladder to help ease the effort of reboarding after going into the water.
Short, aluminum tower with overhead canvas to protect the helm.
The lower corner of a sail. Also, each leg of a zigzag course.
A fitting or object that goes all the way through a hull.
A bar connected to the rudder and used to steer the boat.
A small, outboard motor that uses a handle fitted with engine controls to steer instead of a steering wheel.
Adjustable jack on the trailer tongue that raises and lowers the coupler.
The measurement of trailer weight when loaded with a boat on the hitch ball.
The hull above the waterline. Also, everything above deck as opposed to below deck.
Usually mounted directly to the frame of the trailer. They have four rubber cords in the axle tubing that resist torsion, create suspension, and provide shock absorption. As you drive down the road, the rubberized cords compress and offer even wheel suspension which gives a smoother ride with less vibration.
Maximum weight a vehicle is rated to tow.
Forward portion of a trailer where the coupler is mounted.
Device that uses a crank and cable to assist in launching and retrieving a boat.
An electronic sensing device mounted in a boat’s bilge or at the bottom of the transom to provide data for a depth sounder.
The rear section of the hull connecting the two sides.
A plastic hose and shower head located near the transom that draws from a fresh water supply.
A pleasure boat more than 25 feet in length with a displacement hull.
The way a boat floats in relation to the horizon, bow up, bow down or even. Also, to adjust a boat’s horizontal running angle by directing the outboard or stern drive’s thrust up or down. Also, to set a sail in correct relation to the wind.
Hydraulically adjusted horizontal plates located on the bottom of the transom that control the trim angle of a boat at speed.
A type of boat with three side-by-side hulls, the center of which is usually larger with crew accommodations.
To fish by towing an array of baited lines or lures behind the boat.
Direction and velocity of wind as measured on land, distinct from apparent wind.
Tall aluminum tower used for spotting fish in the distance, often equipped with a second set of helm controls.
A gasoline- or diesel-powered internal combustion engine that takes two cycles or strokes of the piston to complete its power phase. Also called two-stroke engine.
A boat in motion.
A light installed below the water line of the hull. Usually on the transom.
A type of small, open powerboat, constructed of either fiberglass or aluminum, with minimal features. These include jon boats, skiffs and work boats.
A bed or berth located in the bow that has a V-shape.
Propulsion system where the drive shaft initially runs forward into a gear box and then runs aft and down through the hull. The driveline forms a V-shape with the gear box at the pivot point.
Compass variable that accounts for the difference in degrees between true north and magnetic north.
Air introduced into a spinning propeller from the water’s surface.
Very high frequency; a bandwidth designation commonly used by marine radios.
Waves created by a moving boat.
A type of offshore fishing boat with a small to mid-size cabin and a perimeter deck that allows easy passage around the entire boat.
The intersection of the hull and the surface of the water.
The coordinates of a specific location.
To raise anchor.
Rotating drum device used for hauling line or chain to raise and lower an anchor.
Sails used in normal winds.
To cruise in a motor yacht that typically ranges from 40- to 89- feet long.
To veer off course.
Small pieces of zinc that attach to metal boat and engine components to help protect them from corrosion due to electrolysis, an effect caused when dissimilar metals are placed in a saltwater solution. A softer metal that is sacrificed in order to protect aluminum like lower units or pontoons.